====== Sensors ====== ==== Main page ==== __Figure 1__ – **main page** of chapter SENSORS {{ :en:main_page_sens.jpg?direct |}} This chapter allows you to see which devices are connected to mNVR, check out CAN messages, add sensors or delete them, if there are a necessity you can restore them from trash bin ---- ==== Devices ==== __Figure 2__ – menu **Devices** {{ :en:devices.jpg?direct |}} In menu devices you can check information about devices that are connected to the NVR, their CONNCECT ID, name, version of firmware of devices, and see if there are presets to this device ---- ==== Deleting sensors ==== __Figure 3__ – menu **deleting sensors** {{ :en:deleting_sensors.jpg?direct |}} You can select a couple of them, or choose all, or invert selection and delete sensors which you want, deleted sensors will be moved to trash bin ---- ==== Trash bin ==== __Figure 4__ – menu **trash bin** {{ :en:trash_bin.jpg?direct |}} If you accidentally delete some of your sensors or want to restore old you can do it by **trash bin** menu, you need to select desired sensors and press **restore** button or **discard** if you change your mind ==== Workspace ==== __Figure 5__ – Workspace {{ :en:workspace.jpg?direct |}} There you can check information about your sensor, it current value, category, sensor type, type of content, etc. and if you want to change some parameters you can press Edit button and configure your sensor ---- ==== CAN message ==== __Figure 6__ – CAN message {{ :en:can_message.jpg?direct |}} You can check the state of your devices by pressing CAN messages button, there you can choose the device which you want to check by choosing his address on CONNECT ID, and PGN and see the value which devices will be send. Value will be send in HEX system, to convert in DEC system you need to highlight it and lower right corner will be converted value {{ :en:sensor_status.jpg?direct |}} Also, you can press **Toggle all data table** button for more information ---- ==== Libs manager ==== __figure 7__ – Libs manager {{ :en:libs_manager.jpg?direct |}} If you have a library, that you created manually, you can download it with the help of libs manager. To do that, you need to press **Choose file** button and download file of **.xml** format. To choose **one of preseted** libraries you need to press **Toggle libs list** button, to restore default libraries press **Restore default libs** ---- ==== Bluetooth Low Energy (BLE) scanner adding ==== __Figure 8__ – BLE scanner {{ :en:ble_scanner.jpg?direct |}} If you have BLE sensor you can connect it to mNVR. First you need to scan it by pressing **BLE scan** button and then press **Start** button, after that you can find the desired sensor in the list below, also in this list you can check the information such as: • MAC address • Signal quality level • Distance to the object (in meters) • Information about the signal • Time from the sensor detection After that in sensor menu is need to press **BLE settings** button and add your sensor to **favorite**, in this way you can add sensors from favorite in adding sensor menu __Figure 9__ - BLE settings {{ :en:ble_settings.jpg?direct |}} ---- ==== Adding sensor ==== __Рисунок 9__ – add sensors menu {{ :en:adding_sensor.jpg?direct |}} __Table 1__ - **adding new sensor** parameter description ^Parameter^Parameter description^ |Category|Sensor class, simple or complex| |Sensor number|Sensor number selection| |Sensor type|Sensor type, Internal, CAN, BLE or Computer vision| ---- ==== Internal sensor type ==== The section contains the selection of the sensor subtype, camera number, photo count and its interval, RTSP source and reference to it, the maximum video time associated with the event, the number of photos and frames per second, video time, the interval between photos associated with the event, its count and quality content type, event type, upper and lower limit, average latency, and resubmission interval __Figure 10__ – menu of internal sensor type {{:en:internal_event_type.jpg?direct|}} {{:en:internal_sensor_settings.jpg?direct|}} __Table 2__ – the description of parameters of the subtypes of the sensor internal: ^Parameter ^Parameter description^ |INPUT 0 |Digital input 0| |INPUT 1|Digital input 1| |ANALOG|Analog input 1| |SPEED |Speed sensor| |VOLTAGE|Voltage at the input of the device| |MOVEMENT|The status of the motion sensor on the device| |OVERCURRENT|Overcurrent sensor| __Table 3__ - description of the menu parameters Content type ^Parameter ^Parameter description^ |Photo|Allows you to select the RTSP source, photo count, photo interval, and photo quality | |Fixed time video |Allows you to select the RTSP source and the fixed video recording time| |Event related video|Allows you to select the RTSP source and the maximum video time associated with the event| |Time-lapse video|Allows you to select RTSP links, the number of photos, the interval between them and the number of frames per second| |Event centered video |Allows you to select RTSP links and video time| |Event related photo|Allows you to select the RTSP source, the interval between the photos associated with the event, their quantity and quality | |Фото + Email|Allows you to select the RTSP source, photo count, interval between them and their quality| ---- __Figure 11__ – types of the content {{:en:0_content_type.jpg?direct|}} {{:en:1_content_type.jpg?direct|}} {{:en:2_content_type.jpg?direct|}} {{:en:3_content_type.jpg?direct|}} {{:en:4_event_type.jpg?direct|}} {{:en:5_content_type.jpg?direct|}} {{:en:6_content_type.jpg?direct|}} {{:en:7_content_type.jpg?direct|}} {{:en:8_content_type.jpg?direct|}} ---- ==== CAN Sensor type ==== In the section you can select the type of device and find out information about it, device variable, camera number, photo count and its interval, RTSP source and link to it, maximum video time associated with the event, number of photos and frames per second, video time , the interval between the photo associated with the event, its count and quality, the type of content and event, the upper and lower limit, the average waiting time of the bus address CAN, PGN and CAN settings __Figure 12__ - menu of CAN sensor type {{ :en:can_sensor_menu.jpg?direct |}} __Table 2__ – the description of parameters of the CAN sensor settings: ^Parameter ^Parameter description^ |Available device libs|Available preset for connected devices| |Current device variable |Available variables for devices| |Address |CONNECT ID| |Bitness|Amount of bit the will be send by defined PGN| |Start bit|Initial value of the bit| |Bit total|The total number of bit| |Timeout |The pause between sending values| ---- ==== Computer vision ==== In the section you can select the type of event, camera number, photo count and its interval, RTSP source and link to it, maximum video time associated with the event, number of photos and frames per second, video time, interval between photos associated with event, its count and quality content type and events upper and lower limit, average latency and forwarding interval __Figure 13__ - menu of Computer vision sensor type {{ :en:computer_vision_sensor.jpg?direct |}} ---- ==== Adding complex sensor ==== When you create **two** or more sensor, you can combine it by creating complex sensor. To do that you need choose the sensor type, set output action time and write expression that should show the relationship between the sensor for their correct operation __Figure 14__ – adding complex sensor menu {{ :en:complex_sensor_menu.jpg?direct |}} To set the **default** settings, click the Default button. To save settings in NVR click **Save settings** button.